Introduction
With Internet of Things (IoT) expanding, the scope of the IoT applications is growing from controlling appliances to monitoring devices (like sensors) and sending e-mails. By sending e-mails from you ESP8266 Module, you can know the status of any sensor you are monitoring or you can receive an emergency e-mail in case of burglary or an intruder alert. So, without further delay, let me show you all the steps required to Send an Email using ESP8266 WiFi Module.
ESP8266 Board
As said earlier, I will be using the DFRobot FireBeetle ESP8266 board in this project to send e-mails. You can use any ESP8266 Module and I have tested this procedure with my ESP-01 ESP8266 Board and it worked just fine.
Since the DFRobot FireBeetle ESP8266 board has all the required components like the MicroUSB Port, 3.3V Regulator, etc. I don’t need to make any extra connections with respect to the board. All I need to do is to plug-in a MicroUSB cable in the port and connect it to a computer (with the drivers being already installed and Arduino IDE is already setup). This is one of the main reasons for choosing the DFRobot FireBeetle ESP8266 board over my regular ESP-01 Module. So, I suggest you to go through the hook-up guide of the DFRobot FireBeetle ESP8266 board as described in the following project: DFROBOT FIREBEETLE ESP8266 REVIEW AND HOOK-UP GUIDE.
SMTP Server Setup
In order to send e-mails from ESP8266 Module, you need to follow the SMTP protocol. Hence, an SMTP Server is required to send the e-mails and the ESP8266 will act as an SMTP Client. I have tried the Gmail’s SMTP Settings several times to send email using ESP8266 but it was not fruitful. So, I have decided to use a third-party SMTP Server and I found “SMTP2GO” as a reliable choice.
So, go to the SMTP2GO website and register with a free account. After creating an account, the first step is to create the SMTP Username and SMTP Password. In fact, the moment you confirm your e-mail address and first login to SMTP2GO, this is the information that you’ll get. Leave the username as it is i.e. the e-mail address and change the SMTP Password with your own choice. Note that this is SMTP Password and is different from the SMTP2GO Login Password. Make a note of the two i.e. SMTP Username and SMTP Password. Now, enter the dashboard of the SMTP2GO app and on the left access bar, click on “Settings” and then on “Users”. In that, you can see the information regarding the SMTP Server and PORT number. It is usually as follows:
SMTP Server: mail.smtp2go.com SMTP PORT: 2525
Note down this information as you need to use this data in the code.
Encoding Username and Password
You need to encode your SMTP Username and SMTP Password to Base64 format with ASCII Character Set. For this, you can either use an Arduino Library or a website called BASE64ENCODE.
Enter your SMTP Username and Password separately and note the encoded content. For example, if your email address is test@gmail.com, it would be encoded as dGVzdEBnbWFpbC5jb20=. And if your password is “testpassword” (excluding the quotes), it would be encoded as dGVzdHBhc3N3b3Jk.
Code
Now, let me show you the necessary code in order to Send an Email using ESP8266.
In the code, make necessary changes like SSID, Password of your WiFi Connection, Sender and Receiver E-Mail Address, Base64 Encoded SMTP Username and SMTP Password.
Explanation of the Code
The initial section of the code is simple used to connect the ESP8266 WiFi Module to the Internet. If the connection is successful, you will get an IP Address. Next is the actual code for sending the e-mail. The code can be divided into 8 stages. Stage 1: In stage 1, you will be connecting to the SMTP Server on a PORT. This is done using the command client.connect(SMTP_SERVER, SMTP_PORT). In response, you will get a 220 code. Stage 2: Greet the SMTP Server with EHLO Command (Previously HELO Command). The command is client.println(“EHLO www.example.com”); If the connection is successful, you will get a 250 Response Code. Stage 3: Stage 3 is to authorize the user with AUTH LOGIN Command. The command is client.println(“AUTH LOGIN”);. You will get a Response 334 for success. Stage 4: Send the encoded SMTP Username and Password one after the other. The commands are client.println(“Base64, ASCII encoded username”); and client.println(“Base64, ASCII encoded password”);. If the authentication is success, you will get a 235 Response. Stage 5: Now its time to send the mail from string where you have to enter the sender’s email address using the format MAIL FROM:<”+String(from)+’>’;. The command is client.println(“MAIL From: sender@gmail.com”); Stage 6: Then send the rcpt to string using the format RCPT TO:<”+String(to)+’>’;. The command is client.println(“RCPT To: receiver@gmail.com”);. Stage 7: Send the “DATA” followed by the Message body of the e-mail. The commands are client.println(“DATA”); client.println(“To: receiver@gmail.com”); client.println(“From: sender@gmail.com”); client.println(“Subject: ESP8266 test e-mail\r\n”); client.println(“This is is a test e-mail sent from ESP8266.\n”); client.println(“Second line of the test e-mail.”); stage 8: Finally, terminate the mail with “.” and send the quit command. client.println(“.”); client.println(“QUIT”); All these commands and responses will be shown in the serial monitor of the Arduino IDE.
If you follow all the mentioned steps, you will be able send an email using ESP8266 successfully. Please help me to solve this issue but i dont have my own sender domain.. Is there any alternative to SMTP2go without using sender domain Can you please help ??? Thanks in advance please help to solve this problem, please Sending From 250 OK Sending To 550 that smtp username’s account is not allowed to send Sending To 550 that smtp username’s account is not allowed to send Can you help me? greetings Juergen Do you mind to share your circuit diagram as well ? Thank you I saw several few peoples has been asking for this error ” 550 that smtp username’s account is not allowed to send ” can you help to give solution for all of us ? Thank you very much “Since you’ve signed up for a free account with a free email address, we require the “Settings > Sender Domains” section be setup and verified before you’ll be permitted to start sending mail through your account. This is a measure we’ve taken to reduce spam as well as improve the deliverability of your outbound mail. If you don’t have your own domain, you’ll need to find an alternative SMTP provider.” now i am trying to send email using google SMTP server… Comment * Name * Email * Website
Δ
